$65.43
$99.45
System board Specification Description System board form factor ATX 24.89 x 24.38 mm (9.8 x 9.6 in) Processor socket Single LGA 1151 CPU bus speed DMI Memory expansion slots 4 DDR4 memory slots Memory type supported DDR4, UDIMM (unbuffered), ECC and non-ECC Memory modes Non-interleaved for single channel. Interleaved when both channels are populated. Memory speed supported 2133MT/s DDR4 Memory protection ECC available on data Maximum memory 64 GB Memory configuration 4GB, 8GB and 16GB non-ECC/4GB, 8GB and 16GB ECC unbuffered DIMMs are supported. ECC and non-ECC memory DIMMs cannot be mixed on the same system. PCI express connectors 1 PCI Express Gen3 slot x 1 mechanical/ x 1 electrical (full height, full length) 1 PCI Express Gen3 slot x 16 mechanical/ x 16 electrical (full height, full length) 1 PCI Express Gen3 slot x 4 mechanical/ x 4 electrical (full height, full length) 1 PCI Express Gen3 slot x 16 mechanical/ x 4 electrical (full height, full length) NOTE: In the PCIe Gen3 (x 16 electrical/x 16 mechanical) slot, if it is not being used for a graphics card, only cards certified as After Market Options for this platform are supported. PCI connectors (5 V) 1 (optional) PCI slot, full height, full length Supported drive interfaces SATA: Integrated (4) Serial ATA interfaces (6 Gb/s SATA). One port can optionally be used for eSATA. RAID 0 and 1 supported. Factory integrated RAID is Microsoft Windows only. RAID 5 is supported by Software XOR. Serial Attached SCSI None Integrated RAID: NOTE: Requires identical hard drives (speeds, capacity, interface) Integrated graphics: Intel HD Graphics 530 (on Core i3/i5/i7-6xxx processors); Intel Integrated Graphics for Xeon processors Based on Unified Memory Architecture (UMA) – a region of system memory is reserved and dedicated to the graphics display. Support for Mic1 DVI-D and 2 DP 1.2 graphics ports integrated in motherboard; Supports up to three simultaneous displays across DP and DVI-D outputs. 1 DVI-D and 2 DP 1.2 graphics ports integrated in motherboard; Supports up to three simultaneous displays across DP and DVI-D outputs. Maximum resolution supported on DVI- D ports: 1920 x 1200 at 60Hz Maximum resolution supported on DP 1.2 ports: 3840×2160 at 60Hz Network controller: Integrated Ethernet PHY Connection I219LM. Management capabilities: WOL, PXE 2.1 and AMT 9 External SATA (eSATA): External SATA (eSATA): 1 port eSATA capable (SATA 3) with optional eSATA after-market option cable kit IDE connector: No Floppy connector: No Serial: 1 internal header (requires optional serial port adapter kit) 2nd Serial: No Parallel: 1 internal header (optional parallel port adapter required) HD integrated audio: Yes USB connectors Front: 2 USB 3.0, 1 USB 2.0, 1 USB 2.0 charging data port Rear: 4 USB 3.0, 2 USB 2.0 Internal: 1 USB 3.0 and 3 USB 2.0 ports available as 2 separate 2 x 6 (3.0 x 1.2.0 x 1) and 1 x 6 (2.0 x 1) headers: supports 1 HP Internal USB port kits plus one USB 3.0 SD card reader HD integrated audio Yes Flash ROM Yes CPU fan header Yes Chassis fan header 1 rear system chassis fan header Front control panel/speaker header Yes CMOS battery holder – lithium Yes Integrated trusted platform module Integrated TPM 1.2 The TPM module disabled where restricted by law, i.e. Russia Power supply headers Yes Power switch, power LED and hard drive LED header Yes Clear password jumper Yes Keyboard/mouse USB or PS/2 Operating voltage range 90-269 VAC Maximum: 890 btu/hr (224 kcal/hr) Rated voltage range 100-240 VAC Rated line frequency 50-60 Hz Operating line frequency range 47-66 Hz Rated input current 6A at 100-240 V Heat dissipation Typical: 444 btu/hr (112 kcal/hr) Maximum: 1484 btu/hr (374 kcal/hr) Power supply fan 80 x 80 x 25 mm (3.1 x 3.1 x 0.98 in) 4-wire PWM ENERGY STAR qualified (config dependent) Yes CECP compliant at 220V Yes FEMP standby power compliant Yes, with wake-on-LAN disabled: < 2 W in 55 – power off Built-in self test (BIST) LED Yes Surge tolerant full ranging power supply (withstands power surges up to 2000 V) Yes Hood lock header Yes ErP Lot 6- Tier 1 compliance at 230 V Yes ErP Lot 6- Tier 2 compliance at 230 V Yes Environmental requirements Temperature: Operating: 5° to 35° C (40° to 95° F) Non-operating: -40° to 60° C (-40° to 140° F) Humidity: Operating: 10% to 90% (non-condensing) Non-operating: 5% to 95%, 38.7° C (101.6° F) maximum wet bulb temperature Maximum altitude: Operating: 3,000 m (10,000 ft) Non-operating: 9,100 m (30,000 ft) Dynamic Operating: 40 g, 2-3 ms, half-sine Non-operating: 160 cm/s, 2-3 ms, half-sine. Square: 422 cm/s, 20 g Vibration: Operating random: 0.5g (rms), 5-300 Hz Non-operating random: 2.0g (rms), 10-500 Hz Cooling Above 1524 m (5,000 ft) altitude, maximum operating temperature is de-rated by 1.8° F (1° C) per 305 m (1000 ft) elevation increase. Physical security and serviceability Specification Description Access panel Tool-less, except for the processor heatsink. Optical drive Tool-less Hard drives Tool-less Expansion cards Tool-less Processor socket Tool-less, except for the processor heatsink Green user touch points Yes, on tool-less internal chassis mechanisms Color-coordinated cables and connectors Yes Memory Tool-less System board Screw-in Dual color power and HD LED on front of computer Yes Configuration record SW Yes Over-temp warning on screen Yes Restore CD/DVD set Consists of an operating system DVD (OSDVD) and a driver DVD (DRDVD). OSDVD restores the original operating system. DRDVD will provide all drivers for the system. The DRDVD may also contain applications that originally shipped with the system for optional installation. Applications can also be obtained from HP.com. OSDVD and DRDVD are orderable with the system and available from HP Support. Dual function front power switch Yes, causes a fail-safe power off when held for 4 seconds Padlock support Yes (optional): locks side cover and secures chassis from theft 0.22 in diameter padlock loop at rear of system Cable lock support Yes, Kensington Cable Lock (optional): Locks side cover and secures chassis from theft 3 mm x 7 mm slot at rear of system Universal chassis clamp lock support Yes (optional): Locks side cover and locks cables to chassis. Secures chassis from theft and allows multiple units to be chained together when used with optional cable Threaded feature at rear of system Solenoid lock and hood sensor Yes (optional) The Solenoid Hood Lock eliminates the need for a physical key by making the chassis lockable through software and a password. You can also lock and unlock the chassis remotely over the network. The sensor kit detects when the access panel has been removed. Rear port control cover Yes, locks rear IO cables to prevent cable theft Serial, parallel, USB, audio, network, enable/disable port control Yes, enables or disables serial, USB, audio, and network ports Removable media write/boot control Yes, prevents ability to boot from removable media on supported devices (and can disable writes to media) Power-on password Yes, prevents an unauthorized person from booting up the workstation Setup password Yes, prevents an unauthorized person from changing the workstation configuration 3.3 V aux power LED on system PCA Yes NIC LEDs (integrated) (green and amber) Yes CPUs and heatsinks A T-15 Torx or flat blade screwdriver is needed to remove the CPU heatsink before the CPU can be removed. CPU removal is tool-less Power supply diagnostic LED Yes Front power button Yes, ACPI multi-function Front power LED Yes Front hard drive activity LED Yes, white Front ODD activity LED Yes Internal speaker Yes System/emergency ROM flash recovery Recovers corrupted system BIOS. Cooling solutions 92 x 92 x 25 mm 4-wire PWM (non-serviceable) Power supply fans 92 x 92 x 25 mm 4-wire PWM (non-serviceable) CPU heatsink fan Mainstream (<= 65 W; 92 mm x 92 mm x 52.5 mm Chassis fan No Memory heatsink fan Advanced Configuration and Power Management Interface (ACPI). Allows the system to wake from a low power mode and controls system power consumption, making it possible to place individual cards and peripherals in a low-power or powered-off state without affecting other elements of the system HP PC hardware diagnostics UEFI HP PC Hardware Diagnostics (UEFI) enables hardware level testing outside the operating system on many components. The diagnostics can be invoked by pressing F2 at POST, and is available as a download from HP Support. Access panel key lock No ACPI-ready hardware Advanced Configuration and Power Management Interface (ACPI): Allows the system to wake from a low power mode. Controls system power consumption, making it possible to place individual cards and peripherals in a low-power or powered-off state without affecting other elements of the system. Integrated chassis handles Rear recessed handle; optional optical bay front handle available. Power supply Requires T15 Torx or flat blade screwdriver PCI card retention Yes, rear (all), middle (optional), front (full-length cards with extender) Flash ROM Yes Diagnostic power switch LED on board Yes Clear password jumper Yes Clear CMOS button Yes DIMM connectors Yes Category: Desktops
Workstations
